How To Build Bookcase

How To Build Bookcase – Create a DIY bookshelf for a durable, space-saving and stylish display in your home.

If your books and photos are still visible on two boards stacked in a pile of bricks, here’s good news: Adding a built-in unit doesn’t require a handyman, a full-fledged workshop, or thousands of dollars. A bookshelf for your home. All he needs is mainly solid veneer plywood and a circular saw. By gluing short pieces of support to long pieces of wood, you can make thick boards that are hinged to accept shelves. The solid wood finish that covers all the edges of the pump hides your smarts, leaving you with furniture worthy of a great library.

How To Build Bookcase

Typically, built-in bookcases are made from solid wood planks that are carefully manipulated to create tight holes that accommodate each shelf. But split lumber is expensive—enough oak for an 8-foot bookcase, for example, costs thousands of dollars. Wood plywood is not only less expensive, but in many cases stronger than hard soft woods like pine. Most hardwoods have the main materials: birch, maple and oak veneers. If you are planning to stain your bookcase, the best wood to use is birch, and Maple provides a variety of stains. But there are special orders that make plywood from any type of wood, including mahogany, teak, cherry or walnut. For them, it is better to use a transparent finish and let the beauty of the wood shine through.

Book Shelves Are Too Expensive So I Decided To Just Build My Own. Each Case Costs $55 In Wood. Jog On Over Priced Furniture Stores.

We used oak for the entire frame and doubled the thickness by gluing it to the sides or legs of the bookcase and nailing it to long boards. (Cutting grooves into a single board will compromise its strength.) Rough board edges are hidden by solid wood finishes.

The hard part of working with the siding is cutting the 4-foot-wide boards to the required widths for the framing and shelves. An 8-foot sheet is difficult to cut straight on a circular saw, and compounding on a portable table saw is dangerous. Your best bet is to see if the lumber yard has a commercial table saw for a clean, straight cut. Many yards offer discounts of a dollar or more each. Determine how deep you want the bookcase frame and shelves to be, cut 11/16 inches for extra 5/4 hardwood trim depth, then have the lumber yard cut all the sheets into boards that width. Once home, you can use a circular saw to cut these narrow pieces to length.

Wood Square Cut your composition into boards that are wide enough to match the depth of the bookcase. Before cutting and assembling any pieces, sand all the wood. Paint it or sand it and let it dry.

Measure the height of where the bookcase will go. Cut two bookshelf legs from ripped plywood to this size

How To Build A Tree Bookshelf

Measure the area of ​​your space in three places. Subtract 1½ inches from the smallest measurement. Cut the shelves from the pump to this length. (Don’t forget to cut off the top.)

If you want the shelves to be at different heights to accommodate books of different sizes, you need to mark the legs where the supports are located. Hold one leg against the wall and mark where the bottom of each shelf will go. Try juxtaposing shelves with nearby architectural details such as baseboards, windows and mantels.

Press both legs together in the same way and place them on the table. Use a framing square to transfer shelf marks from one board to another. Then place a pump scraper on each row and mark the width of each shelf.

Measure between the lines to find the dimensions of the support pieces. Quickly use a circular saw with a square guide to cut the posts out of plywood with top grooves. Cut the top posts ¾ inch short.

Diy Basic Bookshelf

The bookshelf has a support plate to cover the space below the bottom shelf, so the bottom supports need to be moved back. Using a circular saw, carefully cut them to a depth of ¾ inch.

Glue and nail the posts to the legs: squeeze the S-shaped glue from the bottom of one leg to the first location line. Align the bottom support piece with the bottom and back edges of the board. Nail the squares with 3D nails.

Place the following supports using the plywood as spacers the size of the shelf. Glue and nail. Continue attaching the posts on the left side in this manner until the top posts are in place, leaving no more than ¾ inch from the top edge. Repeat with the other leg.

Cut a 2½-inch-wide piece of plywood to make the hanging strips that will attach the bookcase to the wall. Cut it 1½ inches shorter than the shelves.

How To Make Diy Built In Bookshelves: 17 Ideas & Tutorials

Place both feet on the rear ends, the legs facing each other. Place the hanging plate between the upper supports, flush with the top and back edges.

Using a drill fitted with a ⅛-inch combination bit, drill two pilot holes for each leg. Drill through the leg and support into the hanging beam. Screw the suspension strap to the legs with 2½-inch wood screws.

Slide the bottom shelf into place for support. Screw the assembled frame back into place. Place the top of the books on the supports and mounting board. Drill countersunk holes in the ends of the bookshelf – two for each post and one every 8 to 10 inches for the mounting strip. Glue and screw into place at the top.

Slide all the shelves into the frame. If some need reinforcement, use a rubber mallet to gently tap into place.

How To Build Diy Bookshelves For Built Ins

Check the level of the bookshelf. Level each shelf. If you need to lift one side, touch the thin sticks under the leg.

Hold the level vertically to check the pipe drawer. Add loops if necessary. Once the entire room is dry and level, tap the screws around the bookcase to make sure the frame sits snugly over the opening where there is a gap in the wall. Score the flaps with a knife, then pull them towards the edge of the bookcase.

Use a stud finder to find and mark where the wall studs go under the mounting strip.

Using the included drill, drill screw holes and counter holes in the mounting bar on each marker. Secure the bookshelf to the wall with 2½-inch screws through the pilot holes.

Diy Floating Bookcase

Cut a piece of plywood to act as a nail for the batting board – the same size as the bottom posts on the frame. Slide it under the center of the bottom shelf. Attach the top edge of the shelf with 6D trim nails.

Measure the hole under the bottom shelf. Cut a piece of plywood to fit snugly in place. Insert this kick board into the hole with nails and support edges. It should be folded in front of the bookshelf. Attach it to each of the posts and the center nail with two 6d finish nails.

Use ½ trim to finish the sides and top of the bookcase. Trim can be hinged or flush to the inside edge.

Hold the bookcase legs firmly against the wall. Use a level to adjust the leveling until it is level. Touch it with a 6D nail.

How To Build A Bookshelf

Find a wide gap between the trim and the wall. Open the inscription to widen the opening. Run the dot along the wall so that the pencil traces the outline of the wall to the finish. Remove the edge and cut along the scribe line with plaster.

Use a 1x cut to create a tapered, finished edge on the front of the shelves. Hold the 1x cutter against the front of the shelves and cut to one side to ensure that these nose pieces fit snugly between the side cutters. Mark where the back of each piece meets the other side. Cut each strip on the label.

Apply glue to the front of the shelf. Attach the nose with 6D trim nails. Start gluing at one end and as you go down the length, adjust the nozzle so that it is properly attached to the top of the shelf. Similarly, finish each shelf with a nose.

Prepare all the nail heads and fill the holes with putty or wax pencil to match the color of the painted wood. Finally, paint the entire bookshelf with paint, wax, or polyurethane.

How To Build A Bookcase

Creating a tight, gap between the cabinet trim and the wall—a process known as sheet metal—is one of the most important skills that separates true craftsmen from those who rely on veneer. But after the cabinet is tunbi and glued, it is not difficult.

Get the latest news, reliable tips, tricks and DIY Smarts for this old home

How to build a ladder bookcase, how to build a bookcase with doors, how to build secret bookcase door, easy to build bookcase, how to build a revolving bookcase, how to build hidden bookcase door, how to build a simple bookcase, how to build a coffin bookcase, how to build a basic bookcase, how to build a wall bookcase, how to build your own bookcase, how to build a bookcase wall unit